We provide metal roof coating services in Evansville for rusted, leaking, and worn commercial roofs, from full metal systems to silicone, acrylic, foam, and shingle coating.
Our metal roof coating services in Evansville are listed below, each with the roof it fits and the one thing we check first.
The main service for steel roofs. Failed screws are replaced, laps stitched and taped, rust primed, and base and top coats sprayed over ribbed or standing seam panels on plants, warehouses, and shops.
A moisture-cured coating that holds up under standing water and strong summer sun, sprayed over primed metal or single-ply membrane on the flatter parts of a roof.
Water-based coats rolled or sprayed in warm, dry weather. Acrylic reflects heat, flexes with the panels, and recoats easily with more acrylic years later.
Closed-cell foam sprayed over firm panels fills the ribs, adds insulation, and forms one continuous surface that a protective coating then covers.
Coating made for asphalt shingles seals light granule loss on flat, attached shingles over offices, churches, and small retail buildings.
Start from what the roof shows from the ground or the hatch. The inspection confirms the choice.
Surface rust, cracked washers, and open laps on a structurally firm steel roof over a plant or warehouse.
Flatter sections where puddles stay for two days or more after a storm, usually near drains and low corners.
Sloped panels with good drainage and factory paint that has chalked or faded in the sun.
Leaks across most of the roof plus a work floor that runs hot in summer and cold in winter.
Shingles still flat and attached on an office, church, or small retail building, with some granules gone.
Curling, brittle, or missing shingles and soft decking mean the shingles are past the point of coating.
The inspection answers that. Call and describe the roof, and we will walk it and recommend one system.
Each service follows the same core steps, adjusted for the system going on the roof.
The roof is walked and probed, insulation is moisture-tested wherever water stood, and the coating system is picked from what the roof actually shows.
Screws, laps, curbs, gutters, and flashings are repaired before anything else, so every coating meets firm, sealed edges at each joint.
Washing and rust treatment follow the coating maker's written instructions, and the primer is matched to the surface under it.
Coatings or foam go on in the passes and thickness the product sheet calls for, checked with a gauge throughout the work.
Products, coats, colors, and repairs are listed in a record that stays with the building for future recoats and inspections.
Answers on choosing between the services.
Rust depth, drainage, insulation needs, and the existing surface point to one system. The written scope explains why that system was picked for your roof and what each step costs, so you can compare it with any other option we list.
A plant can take the full metal system on its main roof and silicone on a flatter addition that holds water. Each system gets its own primer and its own section of the scope, and the joint between the two areas is detailed so it stays sealed.
Photos help us prepare, but rust depth, screw grip, and wet insulation need hands-on checks before any price is written. The roof walk takes place before the scope, every time.
Where panels have failed across most of the roof, the scope lists replacement or a foam recover next to coating, so the options can be compared side by side before you decide.
Big roofs can be split into sections over several seasons, with sealed edges at each break so finished areas stay watertight while the rest waits for its turn.
Crew size, weather, and the amount of repair work set the schedule. The scope lists the planned working days for your roof and the weather each coat needs.
Old patches made with mixed products get adhesion-tested, and the ones that fail come off before primer, so the new coating bonds to a firm surface.
Permit rules change by town and by scope. Before work starts, we confirm with the local office and add any permit step to the roof schedule.
Church halls and school gyms with metal roofs coat like any other building, with the work booked around services, classes, and events.
Panels and racking stay in place, and coating stops at clean edges around each mount, with the flashing at every mount checked first.
You keep the record of products and coats, and a yearly walk catches small damage, clogged drains, and loose screws before they grow.
Tell us about the roof, and we will match it to the right coating service.